Your shopping cart is currently empty.
Bonding and Electrical
Pool Water Bonding and Electrical Components
Electrical Water Bonding is a new National Electrical Code that inspectors are now enforcing.
All "PoolBond" electrical pool bonding fitting are UL approved and will not void any warranties.
Item No.
PBAG
Permacast Item Number PB-AG
UL Listed
10.5 Square Inches of Surface Area
(read more...)Pool Bond Water Bonding Fitting
Pump Mount Water Bonding Fitting
Complies with NEC 680.26(C)UL Listed
10.5 Square Inches of Surface Area
Price:
$34.14
In Stock
Item No.
PB2008
Permacast Item Number PB-2008
UL Listed
10.6 Square Inches of Surface Area
(read more...)Pool Bond Water Bonding Fitting
1 Inch NPT Water Bonding Fitting
Complies with NEC 680.26(C)UL Listed
10.6 Square Inches of Surface Area
Price:
$31.03
In Stock
Item No.
PC08KIT20
Permacast Item Number 08KIT-20
(read more...)Pool Bond Water Bonding Fitting
2 Inch Plumbing Kit for PB-2008
PB-2008 NOT INCLUDED
Includes:- 2" Slip Bushing
- 2" Tee
Price:
$17.51
In Stock
Item No.
08KITAG
Permacast Item Number 08KIT-AG
(read more...)Pool Bond Water Bonding Fitting
Above Ground Plumbing Kit for PB-2008
PB-2008 NOT INCLUDED
Includes:- 1-1/2" Threaded Tee
- 1-1/2" Threaded Bushing
- 1-1/2" Threaded Nipple
Price:
$26.60
In Stock
Item No.
CMP25810500000
Custom Molded Products Item Number: 25810-500-000
(read more...)Pool Defender Above Ground Pump Water Bond
- Install Pool Bonding to a Standard Above Ground Pool Pump through the Strainer Drain Plug
- No Special Tools Required for Installation
- Stainless Steel Coil Sits Below Pump Basket
- Bolt Connector Attaches to Pool Bonding Wire
- Meets Requirements of NEC 680.26 (C)
Price:
$24.25
In Stock
Item No.
CMP25810850000
Custom Molded Products Item Number: 25810-850-000
(read more...)Pool Defender Economy Union Water Bond
- Install Pool Bonding to a Standard Above Ground Pool Filter at the Hose Connection
- No Special Tools Required for Installation
- Bolt Connector Attaches to Pool Bonding Wire
- Meets Requirements of NEC 680.26 (C)
- 1-1/2" MPT x Hose
Price:
$40.58
In Stock
Item No.
98210500
Pentair Pool Products Part Number 98210500
Used for Grounding and Bonding Pool Pumps and Pool Heaters
(read more...)Used for Grounding and Bonding Pool Pumps and Pool Heaters
Price:
$15.42
In Stock
Price:
$34.14
Currently Unavailable.
Item No.
BS680AG
Generic Item Number: BS680AG
ABOVE GROUND MODEL
BOND SAFE 680
(Patent Pending and UL Listed)
IMPORTANT SAFETY INSTRUCTIONS
The integrity of the bonding connection should be periodically inspected.
READ AND FOLLOW ALL INSTRUCTIONS
Included: One bonding plate, (1) rubber sealing washer, (2) flat washers, (2) lock washers, (2) nuts and (1) bonding lug
Instructions for Installation:
1. First, drill a 3/16 inch hole in the rear of the skimmer casing where the skimmer basket is held. Locate the bonding plate as close to the bottom of the skimmer casing as possible allowing for enough room inside of the skimmer for the bonding plate.
2. Place the rubber washer on the base of the threaded stud on the bonding plate.
3. Push threaded stud through the 3/16 inch hole previously drilled.
4. Secure with a flat washer, lock washer and nut in that order. *CAUTION: Do not over tighten*
5. Use the 2nd flat washer, 2nd lock washer and 2nd nut to secure the bonding lug.
6. Last, connect solid copper wire, not smaller than no. 8 AWG, to the bonding lug. The copper wire should also connect to motor and all metal parts of the swimming pool within 5 ft. of the inside wall of the swimming pool.
Price:
$59.29
In Stock
Item No.
BS680IG
Generic Item Number: BS680IG
INGROUND MODEL
BOND SAFE 680
(Patent Pending and UL Listed)
IMPORTANT SAFETY INSTRUCTIONS
The integrity of the bonding connection should be periodically inspected.
READ AND FOLLOW ALL INSTRUCTIONS
Included: One bonding plate, (1) rubber sealing washer, (2) flat washers, (2) lock washers, and (2) nuts and (1) bonding lug
Instructions for Installation:
1. First, drill a 3/16 inch hole in the rear of the skimmer casing where the skimmer basket is held. Locate the bonding plate as close to the bottom of the skimmer casing as possible allowing for enough room inside of the skimmer for the bonding plate.
2. Place the rubber washer on the base of the threaded stud on the bonding plate.
3. Push threaded stud through the 3/16 inch hole previously drilled.
4. Secure with a flat washer, lock washer and nut in that order. *CAUTION: Do not over tighten*
5. Use the 2nd flat washer, 2nd lock washer and 2nd nut to secure the bonding lug.
6. Last, connect solid copper wire, not smaller than no. 8 AWG, to the bonding lug. The copper wire should also connect to motor and all metal parts of the swimming pool within 5 ft. of the inside wall of the swimming pool.
Price:
$59.29
In Stock